EXPIRY DATE: 10/05/2020 SIKA Sikalayer Acoustic Kit - 6m2 - To be used before 10/05/2020, ready-to-use kit for laying parquet on an acoustic underlay to reduce noise and for gluing by bead. The kit consists of 2 x 3m rolls of SikaLayer-05 and 12 cartridges of SikaBond 52 Parquet. Advantages : SikaLayer-05: Easy application. Suitable for tongue-and-groove parquet flooring laid in strip form. Suitable for non-heated floors Excellent impact sound insulation SikaBond 52 Parquet : Fast curing. Sanding of glued parquet after 12 hours at +23C and 50% RH. Excellent initial tack Especially suitable for nervous woods such as beech, maple and bamboo. Suitable for gluing parquet directly onto old tiles Suitable for laying on underfloor heating Makes up for flatness defects Elastic glue which reduces the sound of impact noises Features : SikaLayer-05: Density: approx. 30 kg/m3 Thickness: 5 mm Flash point: 420 / 440 C Colour: Black Consumption: same surface as the parquet to be glued. SikaBond 52 Parquet : Density: approx. 1.29 Skin formation time: approx. 60 min. at +23 C and 50 % RH. Curing speed: approx. 3.5 mm / 24 hours at +23 C and 50 % RH. Colour: brown parquet Substrate temperature: above +15 C when laid on a non-heated floor / approx. 20 C when laid on a heated floor. Packaging : x1 Sikalayer SIKA Acoustic Kit - 6m2 - To be used before 10/05/2020 Delivered in its original packaging Tips : Supports SikaLayer-05: Sand any protruding parts, sand, smoothen, if necessary, with a suitable hydraulic binder-based filler. Allow the levelling compound to dry completely and make sure that the adhesive adheres well. Thoroughly vacuum clean the Supports SikaBond 52 Parquet: Concrete / Cement screed: must be sanded and thoroughly cleaned by vacuumingAnhydrite screed / Anhydrite fluid screed: must be sanded and thoroughly cleaned by vacuuming just prior to gluing the parquet, refer to the CSTB technical advice of the substrate.Vitrified/old tiles: must be degreased with Sika Aktivator 205 or sanded and then carefully vacuumed off.wood panels, plasterboard: must be glued (except DTU 51.3) or screwed to the intermediate frame. For floating floors and other surfaces: consult our technical department. Can be applied without primer on floors based on hydraulic binders, anhydrite floors (refer to the CSTB technical notice of the substrate), chipboard, concrete and tiles. On hydraulically bonded floors with excessive residual moisture or old rigid adhesive residues or on substrates with low cohesion, use Sika Primer MB FR or Sika Primer MR Fast. APPLICATION Unroll the SikaLayer 05 underlayment onto the substrate along the entire length of the room, corresponding to the lengthwise direction of the boards. The recesses are therefore perpendicular to the length of the blades. Cut the end of the first strip at the level of the walls, frame uprights or skirting boards with a cutter, without contact or upward movement, while maintaining a suitable peripheral clearance. The strip forms a laying surface where traffic on the bare underlay will be limited to avoid any alteration. Apply SikaBond 52 Parquet Adhesive into each recess with the V-opening nozzle (8 x 10 mm). Lay the flooring backwards on the first strip of underlay and gradually check that the glue is in good contact with the flooring before it forms a skin. Unroll the second strip of underlay. The various strips will be laid edge to edge, without overlapping, over the entire surface to be covered with parquet, as they are laid. Make sure that the boards to be laid on the strip seams are glued. Otherwise, remove the foam at the junction of the belts by cutting with a cutter. The uneven flatness of the boards can be loaded with, for example, a packet of boards to obtain a good contact with the glue until complete drying. Use Sika products with care. Before use, please consult the manufacturer's product manual available on the sika.com website.
